Build A Stevenson Screen How To Build A Shed Roof Over A Porch Log Cabin 12x16 Build Video Firewood Shed Floor Ideas Building Simple Wood Tool Sheds Also your view of. Wood Shed Plans – Complete Blueprints for Making a Shed. Here are the wood shed plans for a traditional style timber frame shed. ![]() This 8 x 1. 0 feet shed hasa simple designeasy to build joints. The clean and simple styling of these outdoor shed plans give a rustic and traditional look but at same time makes it easy to add custom details to these wooden shed plans. Step 1 Prepare the foundation site with a 4″ deep layer of compacted and leveled gravel. Cut three 6 x 6 treated timber skids as shown in the shed construction blueprints. Place the skids following the FLOOR FRAMING PLAN . Lay a straight 2 x 4 across the skids to make sure they are level. ![]() ![]() Step 2 Cut two 2 x 6 rim joists and nine joists . Assemble the floor frame with galvanized nails, as shown in the FLOOR FRAMING PLAN. Check the frame to make sure it is square by measuring the diagonals. Step 3 Position the floor frame on top of the skids and measure the diagonals to make sure it’s square, install joist clip angles at each joist along the two outer skids with galvanized nails Toenail each joist to the center skid. Step 4 Install the tongue- and- groove plywood floor sheathing, starting with a full sheet at one corner of the frame The flooring should extend to the outside edges of the floor frame. Step 5 To prepare the wall posts, cut six 4 x 4 posts (9. On the four corner posts, mark for 3 1/2″ long x 1 1/2″deep notches (to accept the girts) on the two adjacent inside faces of each post Start the notches 4. Step 6 Mark the door frame posts for notches to receive a girt at 4. FRONT FRAMING ELEVATION. Remove the waste from the notch areas with a circular saw and clean up with a broad wood chisel. Test fit the notches to make sure the 4 x 4 girts will fit snugly. Step 7 Position the post bases so the posts will be flush with the outsides of the shed floor, install the bases with 1. The insides of the door posts should be 2.
Brace each post so it is perfectly plumb, and then fasten it to its base using the base manufacturer’s recommended fasteners. Step 8 Cut two 4×6 beams at 1. Notch the ends of the beams for half- lap joints: Measure the width and depth of the beams and mark notches equal to the width x 1/2 the depth, orient the notches as shown in the framing ELEVATIONS . Cut the notches with a handsaw, then test- fit the Joints, and make fine adjustments with a chisel. Step 9 Set an 8- ft. Tack the other 8- ft. Then, position the 1. Measure the diagonals of the front wall frame to make sure it’s square, and then anchor the beams with two 6. Step 1. 0 Reinforce the beam connections with a metal post- beam connector on the outside of each corner and on both sides ol the door posts using the recommended fasteners install an L- connector on the inside of the beam- to beam joints; see the EAVE DETAILStep 1. Cut eight 4×4 corner braces (2. Step 1. 2 Measure between the posts at the notches, and cut the 4×4 girts to fit. To allow the girts to meet at the corner posts, make a 1/2 x 1/2 ” notch at both ends of the rear wall girts and the outside ends of the front wall girts, install die girts with construction adhesive and two 2. Step 1. 3 Frame the roof: cut two pattern rafters using the rafter TEMPLATE , Test- fit the patterns, and then cut the remaining ten rafters. Cut the 2 x 6 ridge (1. Install the rafters and ridge using 2. Cut four 2 – 2s to extend from the roof peak to the rafter ends, and install them flush with the tops of the end rafters; see the GABLE OVERHANG DETAIL of the timber frame shed plans. Add framing connectors at the rafter- beam connections (except at the outer rafters). Step 1. 4 Cut four 2×4 collar ties (5. Install the ties 1. FRAMING ELEVATIONSStep 1. Install the 1 x 8 siding on the front and rear walls so it runs from the 2 x 2s along the end rafters down to 3/4″ below the bottom of the floor frame. Fasten the siding with 8d corrosion- resistant finish nails or siding nails. Don’t nail the siding to the door header in this step. Step 1. 6 Cover the rafter ends along the eaves with 1 x 4 subfascia, flush with the tops of the rafters; see the EAVE DETAIL. Install the 1 x 6 fascia and 1 x 2 trim at the gable ends and along the eaves, mitering the corner joints. Keep the fascia and trim 1/2″ above the rafters so it will be flush with the roof sheathing. Step 1. 7 Rip the plywood soffit panels to fit between the wall framing and the fascia; install them with 3d galvanized box nails; see the EAVE DETAIL. Apply siding along the side walls, butting the top ends up to the soffits. Step 1. 8 Deck the roof with 1/2″ plywood sheathing, starting at the bottom corners. Cover the sheathing with building paper, overhanging the 1 x 2 fascia trim by 3/4″ install the cedar shingle roofing or asphalt shingles following the steps on pages 5. Finish the roof at the peak with a 1 x ridge cap. Step 1. 9 Construct the door frame from 3/4 x 4 1/4″ stock. Cut the head jamb at 3. Fasten the head jamb over the ends of the side jambs with 2 1/2″ deck screws install the frame in the door opening using shims and 1. Add 1 x 2 stops to the jambs, 3/4″ from the outside edges. Step 2. 0 Build the door with seven pieces of 1 x 6 siding cut at 8. Fit the boards together, then mark and trim the outer pieces so the door is 3. Z- bracing with adhesive and 1 1/4″ wood screws, as shown in the DOOR DETAIL . Install flashing over the outside of the door, then add 1 x 3 trim around both sides of the door opening, as shown in the DOOR JAMB DETAIL. Hang the door with two or three strap hinges.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
November 2017
Categories |